• Welcome to the Checkmate Community Forums forums.

    You are currently viewing our boards as a guest which gives you limited access to view most discussions, articles and access to our other FREE features.
    By joining our free community you will be able to:

    » Interact with over 10,000 Checkmate Fanatics from around the world!
    » Post topics and messages
    » Post and view photos
    » Communicate privately with other members
    » Access our extensive gallery of old Checkmate brochures located in our Media Gallery
    » Browse the various pictures in our Checkmate photo gallery

    Registration is fast, simple and absolutely free so please, join our community today!

    If you have any problems with the registration process or your account login, please contact support by clicking here or by using the"contact us" link at the bottom of the page.

" For Sale" 28p Trophy Plus

kalugs22

kalugs22

Well-known member
I have a 28 pitch Trophy Plus that is a little too steep for the pulsare so I have no need to keep it. I'm going to say it is an 7-8 out of 10 there is 1 tiny ding in the edge of one of the blades and a couple little scuffs, not sure what they are from, nothing deep that can't be polished out.

$350obo to your door!

or Trade for a 25p Fury.

6D-FDFCDF5A63C1-11532-0000048D00F7E1B3_zpsa2664743.jpg02-53D6AD7B72AF-11532-0000048D06E3C664_zps5475f8a8.jpgEE-9432FE7E96B6-11532-0000048D0D1F247E_zpsbafae5c4.jpg6B-91291164BA62-11532-0000048D175727E7_zps95fdbc55.jpg02-98CC370D565F-11532-0000048D1D68B14E_zps3f5564bb.jpg62-6B625D065CB2-11532-0000048D2243D610_zps393cabd3.jpgFA-7EBF69E9CC92-11532-0000048D4771D2D0_zpsa4faa444.jpg
 
what engine package are you turning? I think this is the prop I'm looking for. just got the 2013 250 pro xs with standard 1;75 gear. will this motor turn that prop with the 2100 BR hull?
 
jaja said:
what engine package are you turning? I think this is the prop I'm looking for. just got the 2013 250 pro xs with standard 1;75 gear. will this motor turn that prop with the 2100 BR hull?
Click to expand...

250 Pro XS on a 2100br won't be a problem. I can spin it 5200rpm with my 2000 225 Optimax at 2.5-3" below the pad on my 2100br. You should easily spin it into the upper 5000's.
 
If you would raise your motor up where it needs to be, you can turn it. Thats what I had on my 225opti and 2000 Pulsare and was hitting the rev limiter at 79mph. But 3" below the pad is holding it way back!
 
yes I have the 6' bobs plate that I can move up and down so it can be put at the desired height.
 
boatman4021 said:
If you would raise your motor up where it needs to be, you can turn it. Thats what I had on my 225opti and 2000 Pulsare and was hitting the rev limiter at 79mph. But 3" below the pad is holding it way back!
Click to expand...

Ok Boatman how did you have your 2000 setup? I went back through some threads and saw you were 13.5 back and 1" above the pad? What gearcase were you running torquemaster? I also saw where you took the torque tamer off?

I am 13.5 back on a hydraulic plate, currently the highest I can get is 1.5" below the pad. I have the stock torquemaster with a bob's torque tamer on it.
 
You need either 2 jack plates stacked, or 1 and a static set back bracket with some lift built in to it. I had 2 jack plates(1manual and 1 hyd) and a stock lower unit with 1.75 gears. If I would have had a nose cone and 1.62 gears, the boat would have ran way faster! If I remember correctly, the torque tamer was scrubbing off about 4 to 5 mph.
 
boatman4021 said:
You need either 2 jack plates stacked, or 1 and a static set back bracket with some lift built in to it. I had 2 jack plates(1manual and 1 hyd) and a stock lower unit with 1.75 gears. If I would have had a nose cone and 1.62 gears, the boat would have ran way faster! If I remember correctly, the torque tamer was scrubbing off about 4 to 5 mph.
Click to expand...

I have an 8" hydrodynamic static plate with no lift, so the only height I'm getting is from the CMC 5.5" Hydraulic Plate and the motor is mounted on the bottom holes. My CMC is older and only has 1 set of motor holes, I am going to drill a set higher so I can gain some height. I will also try removing the torque tamer and see how it does. We ran into a problem when my dad had his enchanter with the torque tamer causing problems and we ended up leaving it off.
 
kalugs22 said:
I have an 8" hydrodynamic static plate with no lift, so the only height I'm getting is from the CMC 5.5" Hydraulic Plate and the motor is mounted on the bottom holes. My CMC is older and only has 1 set of motor holes, I am going to drill a set higher so I can gain some height. I will also try removing the torque tamer and see how it does. We ran into a problem when my dad had his enchanter with the torque tamer causing problems and we ended up leaving it off.
Click to expand...

how about the prop, is it still for sale?
 
You must log in or register to reply here.
Back
Top