Checkmate MX-15 Hull

[starviper10]

I have an MX-15 hull up for sale. It's in pretty rough shape. Needs new stringer, floor, and transom, along with paint. I'll be holding onto the engine and rigging, so this is just a bare hull on a trailer. The trailer is a different one than what I got it with. This one will function fine for a hull restoration, but would likely be under capacity once a motor is mounted to this hull.

If anyone is interested, please feel free to call/text/email/pm me (847-660-9135, remreid12@hotmail.com).

Here is an album of all the pictures I have of the boat:

http://s1328.photobucket.com/user/re...?sort=3&page=1

I'd love to see someone on here restore this one properly.

Thanks,
Remington

 

[Nick616]

The photobucket link did not work for me. . . .

 

[1954bmw]

price????? and are you keeping the trim tabs???? mark

 

[SCT]

Very cool CM project.......good luck Remington!

 

[starviper10]

Sorry for the link. Here are the pictures. Price is $300.

 

[sim]

Very nice! Lotta work but tons of potential.

 

[starviper10]

Still available. $200

 

[starviper10]

$150

 

[JasonRS]

Long shot, but, is it still available?

 

[starviper10]

It's still available. I replied to your email on 12/23/18.

 

[starviper10]

Ok this MX-15 hull is up for consideration again, this time with some other optional components. I have a calkins boat trailer that can go with this boat that has had the hubs, bearings (with bearing buddies), seals, winch, and jack stand all replaced within the last 1.5 years. This is actually the trailer I originally purchased the MX-15 with, then I used it for the MX-14, but I recently have purchased a different trailer for my MX-14, so this trailer is now up for grabs. Over the last 2 years I have put over 1000 miles on this trailer without any issues. Also up for consideration is a short shaft 1969 100hp that runs that can go with this. If a long shaft would be desired, I also have one of those, and another running 100hp powerhead. I also have a set of correct "racing" checkmate branded trim tabs. I also have some rigging components, including some ride guide steering cables, an older style dual ride guide rack & pinion helm, ride guide steering wheel, correct era gauges, controls, power trim pumps systems, and a transom bracket that can raise the engine vertically without any setback. Note that some of these components are located in Fond du Lac, WI while others are located in Cary, IL (I frequently travel between and can move components as needed). Message for pictures
Thanks

 

[capt911]

Trim Tabs Wanted

Ok this MX-15 hull is up for consideration again, this time with some other optional components. I have a calkins boat trailer that can go with this boat that has had the hubs, bearings (with bearing buddies), seals, winch, and jack stand all replaced within the last 1.5 years. This is actually the trailer I originally purchased the MX-15 with, then I used it for the MX-14, but I recently have purchased a different trailer for my MX-14, so this trailer is now up for grabs. Over the last 2 years I have put over 1000 miles on this trailer without any issues. Also up for consideration is a short shaft 1969 100hp that runs that can go with this. If a long shaft would be desired, I also have one of those, and another running 100hp powerhead. I also have a set of correct "racing" checkmate branded trim tabs. I also have some rigging components, including some ride guide steering cables, an older style dual ride guide rack & pinion helm, ride guide steering wheel, correct era gauges, controls, power trim pumps systems, and a transom bracket that can raise the engine vertically without any setback. Note that some of these components are located in Fond du Lac, WI while others are located in Cary, IL (I frequently travel between and can move components as needed). Message for pictures
Thanks

PM sent to you Sir. Restoring a MX16 and interested in your trim tabs. Let me know please
Dave

 

[starviper10]

I'd like the tabs to go with the boat. If I change my mind I'll let you know. Thanks